Raised in California and transplanted to Utah. Married my college sweetheart from Montana, and we are raising 4 nuggets together. I love all things DIY projects and doing them on a budget. I don’t mind messing up and am ok with the 90/10 rule - nothing is perfect over here and it’s fine by me! Encouraging all ‘wanna-be’ DIYers to just get out there and try it! You will be so glad you did.”
I have always wanted to try wallpaper, but the thought of it intimidates me! I pictured it filled with wet glue and mess up’s constantly. And then I heard of Peel-n-Stick Wallpaper DIY and my world changed. How easy does that sound? I had to try out.
So I did my research on the best reviews and the best price point and I found WALL-POPS. They have all sorts of wallpaper ideas, wall murals, and floor tiles. The entire site is like eye candy for your home! I jumped on this and ordered myself some for the new pantry I am working on. Ready to see how it turned out? You will love it! Check out my 60 second tutorial and then follow along for all the steps.
This is a dark photo, but this is the room before I added the wall-paper.
After much time looking on the Wall-Pops website, I decided on the Loft White Brick style that you can find here. It looks so real and was even textured. Yah! They have so many styles to choose from. Make sure you measure properly the amount you will need. I rounded up. So my large wall took 3 rolls of paper.
You will want to follow all the directions on the Wall-Pops website. You clean your wall and remove extra texture if your wall is heavily textured. Mine wasn’t so I got lucky.
You will start on the right side of the wall, 20 inches in. Every few feet going DOWN to the floor measure 20 inches and then create a vertical line for you to follow. According to the directions of their website, this helps you keep your application in a straight line (because each strip is a little over 20 inches.) You only need to measure the first line. After that you will follow the paper with a level.
I double checked my line with my TACKlife lazer level and I was so glad I did. My wall was off a bit and therefore my line was off. I had to re-measure and not base my starting point off of the left wall, since it wasn’t perfectly straight. I actually moved in by one or two millimeters and then started my 20 inch measurement.
You will unroll your paper and make sure you can find the matching ends to the next roll. Then cut off the remaining top so that it goes on to match. You might be able to use that leftover piece somewhere else so don’t throw it away.
It is easier to have two people to do the job. I climbed the ladder and my mom helped to hand me the paper.
As we slowly peeled off the backing, I would make sure it was level and matching the original line I had made with the laser line in Step Two. She would help pull the backing off while I used the flat edge to gently maneuver over the wallpaper the help it adhere to the wall. You use this to flatten the paper and push out any bubbles. I would scrape from the top of the area to the bottom, and then swipe up from the left bottom corner to the right corner.
Once the first piece is complete, I would rub my dry towel firmly over the entire strip to make sure the bubbles were gone and it was pressed into the wall. I didn’t want to use my hand and get grease on the wall.
To cut off excess (I show this in my video) you apply the straight edge of your spackling knife and press it into the edge you need cut off. Then grab your razor and follow it along the base of the spackling knife. You don’t need to press hard. It will cut pretty easily.
I did the same when I was working around the electrical plug. I pulled off the face (turn off electrical first!) and then used my knife to make the cuts. I added back on the face plate.
Another tip I used was the level when adding on the next row of paper. I made sure the strip as over by .5 millimeter onto the already mounted strip (says this in the directions) and then used the level to make sure it wasn’t crooked.
I made a mistake in my measurements on one small section and the bricks did not line up like I had hoped. I had to cut a one inch strip to fill this space in. You can hardly tell it’s there!
Additionally we had to add one inch to the edge of the wall. Once again you can hardly tell that it doesn’t match up perfectly. Up close you can see it, but step back a few feet and it is camouflage.
We love how it turned out! We can’t wait to add our farmhouse window box and pantry shelving to this space!
Note: You can read those posts here and here
Thank you mom for all the help!
TikTok – https://www.tiktok.com/@citygirlmeetsfarmboy
Instagram – https://www.instagram.com/citygirlmeetsfarmboy/
Facebook – https://www.facebook.com/citygirlmeetsfarmboydecor
Pinterest – https://www.pinterest.com/citygirlmeetsfarmboy/
YouTube – https://www.youtube.com/c/citygirlmeetsfarmboy
This site uses Akismet to reduce spam. Learn how your comment data is processed.
A Home Decor & DIY Blog
[…] My first project was to add Peel-N-Stick Wallpaper to spice up the wall. You can see that super simple tutorial here. Next up will be the pantry […]
[…] Project One – Peel and Stick Wallpaper Wall […]
[…] laundry room. You can follow my step by step instructions of Wallpops Peel and Stick Wallpaper here during my pantry […]
[…] Wallpaper […]
[…] of the normal horizontal way. Never tried peel and stick wallpaper before? Check out my posts here and here to see more tutorials on […]
[…] Project One – Peel and Stick Wallpaper Wall […]