One Room Challenge – Shiplap

– One Room Challenge – Week One

thumbnail_IMG_7529

Do It Yourself Shiplap

IMG_8073

 

I am loving this challenge so far, because it keeps me on a schedule and pushes me to get things done.  I am good with a schedule!  Continue to check out all the guests for the One Room Challenge here as well as the 20 influencers participating – its amazing!

Here’s my 6 week outline:

Project One – Shiplap

Project Two – Window Valences

Project Three – Custom Shutters

Project Four – Blinds

Project Five – Decorating

As you know I am working on my living room for this challenge and giving it a facelift.  This is my before:

IMG_7715 copy

 

So this last week I created my design through sketch to visualize what I wanted to have happen (you can read last weeks post here to see all my plans!).  Just a ruler and pencil is all you need!

 

IMG_7751

 

My base change of the room is shiplap.  Thanks to Jo Jo we are all loving this stuff.  I have written an in depth tutorial on shiplap here that is a good resource if you haven’t worked with it before.  This time around I tried some new these that I will share.

Step One – Measure

You will want to measure how much shiplap boards you will need.  You do this by taking the area of the wall and subtracting spaces that will not be used (windows and fireplace in my case).  You can use a measuring tape or a laser measure.  I used a laser measure because my room was so big and I was doing it alone.

I love this one from TACKlife.  It is super easy to use and inexpensive, it’s the TACKLife S2-40M Laser Measure and you can order it here from Amazon for $29.

 

IMG_7781

 

I wasn’t sure how to best get started and learned from a great YouTube tutorial here from TheMrFinneth – it was very helpful.

This laser measure helped me measure the area of the room, windows and fireplace.  My total needed square feet was almost 80 square feet.

Note:  I partnered with TACKlife and HomeRight for this project and loved their products.  These are not affiliate links that I share today, just links for my followers to buy the products if they need them. \

 

IMG_7785

 

Step Two – Purchase Shiplap

Instead of using a plywood board that is ripped (cut) into 6 inch strips, I opted to use the pre-cut MDF shiplap at The Home Depot this time.  The price was not much different and since it was already primed I liked the idea.  It is heavier to work with though (just beware.)  It cost me $100 for the amount that I needed.

 

Screen Shot 2018-04-12 at 4.47.17 PM

 

They also carry Pine Shiplap for a slightly higher price point.

 

IMG_7816

 

I loaded it up and headed home!

 

IMG_7892

 

Step Three – Paint First Coat

I always paint my first coat before I mount it.  This is optional.  I am just not at good painting and I always tape wrong, therefore getting paint on my walls.  So painting first is my option.  I will add another coat when it is up on the wall, but it is not as detailed.

I used a spray gun for this part and I LOVED IT.  These tools are not that expensive and are so handy.  I partnered with HomeRight and tried their HomeRight Super Finish Max Extra C800971 Paint Sprayer, that you can purchase here from Amazon for $99.

 

IMG_7245

 

You have to add water to your paint (I used Sherman Williams that was mixed especially to match my baseboards) according to the directions.  I sprayed outside and let fully dry before bringing into the house.

 

 

Step Four – Finding Studs

You will measure for your studs using a stud finder and mark them throughout the entire wall.   Then will make lines connecting the marks vertical so you can see where each stud is as you nail.  This can be done with a chalk line or a laser level.

I used the Zircon Stud Finder that you can buy here and it works well for only $12!

 

IMG_3916

 

Then I connect the marks I made using my TACKlife Laser Level.  This is a great cross line laser tool that you can purchase here.

 

IMG_7898

 

Using a tripod I was able to keep my line steady and match it up to the marks so I could draw a line.   Once all the studs were found I was ready to add my boards.

 

IMG_7902

 

Step Five – Mount Your Shiplap

Here I used my Ridgid Nail Gun and air compressor.  Here is how to load your gun:

 

 

Now charger your compressor and get ready to nail!  You will have to make sure that you are not following the line of your ceiling because that isn’t always straight.  Here again you will use the Laser Level to help you stay accurate.  You will need your circular handsaw to make the measured cuts.  Generally you will stag your boards like this:

 

IMG_7918

 

You will use a jigsaw to work your way around the not so straight spaces.  Make sure to be VERY careful around the light switches when you have the plate removed.  I would recommend turning off the power to that area to be fully safe.

 

IMG_8028

 

This space was SO HARD.  I cut it a zillion times.

 

IMG_8030

IMG_8031

IMG_8033

 

It took me 3 days to get the shiplap done, and I worked about 3-4 hours day.  I can’t wait to get painting!

Step Six – Spakling

Here is a video I made of what I use for spakling, how I did it and how to clean it off.  Basically you add your spakling, let dry, and sand off!

 

Once this space is ready you will get all the painting done.

So it has been a successful week!  Can’t wait to start working on my window valences now – stay tuned…

 

IMG_8074

 

Love,

IMG_7271

 

 

 

 

 

Do It Yourself – Farmhouse Shiplap

IMG_8239

Ever since Joanna Gaines started sharing her love of shiplap, I have totally been crushin on it.  I knew I needed some in my home.  I put it off for years and finally last week had the time and the guts to tackle it.

I researched a lot of ways for it to be done and wanted to see if I could install it all by myself.   Mr. Farmboy is always willing to help, but I just wanted to see how possible it was for one person to get it all done.  And now I can say – IT IS POSSIBLE!  It’s not easy and takes a lot of time when you are on your own, but it is possible.  Would I recommend it?  If you are all you have – heck ya.  If you have help though?  Use it – it’s a lot of work alone.  Alright now, here we go…

Continue reading “Do It Yourself – Farmhouse Shiplap”

DIY – Using The Home Depot’s Cutting Center

IMG_7410

Welcome to CITYGIRLMEETSFARMBOY!  We are so glad you are here.  Click here to be added to our email list so you will never miss our DIY projects – we can’t wait to have you!  Want to see some more amazing project using The Home Depot Cutting Center and WOOD WALLS (our favorite)?  Click here!

IMG_7842

I know, I know – why would anyone write a blog post about getting wood cut at The Home Depot?  Well, for years I was to nervous to ask The Home Depot to cut my wood for me, thinking they would treat me weird or something.  I was so insecure about my building skills that I felt I couldn’t risk the embarrassment because I didn’t know what I was doing anyway.  After hearing the Shanty Sisters talk about “ripping” plywood and how easy it was, I thought I would give it a try.  Problem was I didn’t even know what “ripping” wood meant.

Continue reading “DIY – Using The Home Depot’s Cutting Center”