Do It Yourself – Farmhouse Sign
Make this sign in 7 simple steps, come join me!
Ever since I started documenting my home decor journey I have been crushin on all these farmhouse signs. You can pay to get one made, and often they aren’t cheap. But if you don’t have the time and you do have the money – go for it! If you want to try and make one yourself, check out this process that is SUPER easy and SUPER inexpensive (under $20!!!). The only downside? It does take your time. But if you turn on some tunes or your favorite book and get to work, you mind find out how much you enjoy this kind of thing.
Check out my 60 second DIY Farmhouse Sign tutorial and then follow along for all the details!
- 1×10 wood board: 4-8 feet long, depending on how many letters you are using
- Stain (I like Minwax Provincial or Walnut)
- White Paint (I use Behr Paint and Primer)
- Paint and staining brush
- Modge Podge
- Mirror image prints
- Frosting knife (or any tool with a rounded edge)
- Corner brackets (optional)
Step One – Stain Your Wood
I chose not to sand down my piece of wood because I wanted it rustic. Feel free to sand your edges before staining if you would like them softer. Grab your stain, darker is better. It will show through the chippy paint areas. I added Weathered Oak first, let dry, then add Provincial around the edges for some darker spots. This isn’t necessary.
P.S. Forgive my grainy photos! I only video taped this DIY and had to take stills from the movie!
Step Two – Add Vaseline
Lets learn how to achieve the chippy look. I have a detailed blog post here on how to achieve the distressed look using wax as well.
Take your vaseline and rub it lightly onto the edges and corners of your board. Miss some spots on purpose. Then add some in sporadic spots on your board. The more you use the more of the stain will show through for your outcome.
Step Three – Paint Your Wood
Add a layer of white paint (or any color your prefer) to your board. It doesn’t have to be super covered well, just “good enough.” I use Behr Paint and Primer – I love it for the chippy look! Let fully dry before the next step.
Step Four – Print & Cut Your Words
This part is a little tricky if you do not know how to print mirror image. Depending on the computer you have, it can be different for each. Here is a link to teach you:
Type out your word and mess with the fonts. I really like Bordeaux Roman Bold LET for my signs. You can fit about 3 letters per sheet if you use the 800 size. If you don’t have that font you can download it here.
Make sure you fiddle with it on your board to make sure it fits before the next step, which is cutting the letters. You will cut as close to the edge as possible, keeping letters connected if you can. This helps the placement goes smoother.
Step Five – Glue Your Letters
You will dip your brush into the modge podge and gentle wipe ON THE INK SIDE of the first set of letters you are going to lay down. Be gentle so you don’t rip your letters. You have to take special care when laying them down because they are sticky. You will only have a few seconds to move them around if you need before the glue thickens up. I had a measuring tape to make sure the top and bottom spacing were the same.
Also make sure to get glue over the entire letter. Every bit of ink must have glue on it to adhere well to the board.
You will press the letters fully onto the board to make sure no bubbles are left behind. Let dry completely according to directions before moving on to the next step.
Step Six – Remove Paper
Here is the fun part! Grab a rag and get it pretty wet. Not dripping, but still really moist. Gently press it onto all of your letters, one at a time. This will start the process and help with removal.
Once that is done, head back to the first letter. You will gently and slowly rub the letter to remove the paper. This will leave the ink on the board. If you rub too much the ink will come off too. If you do rub some ink off, just press it back in place. It will dry fine. It’s ok to have some ink rubbed off if you are going for a really rustic look like I was. This process takes time, but is worth it. It’s going to look amazing!
Step Seven – Chip Your Paint
I like to use my frosting knife because it is round but not sharp. You can use any like tool for this. You will take the edge and start LIGHTLY scratching areas of your wood. The edges and around letters are especially good spots. You can also scrape off any extra paper you may have left that needs to be removed. The more you scrape, the more chippy your board will be!
I added metal brackets to my edges for a more complete look. You can find these in the knob and drawer handle isle at Home Depot! Spray paint the color you want and drill them on.
Your all done! Such a fun sign for a great price point. Let us know how yours turns out!